Shelter Construction Accessories
Approx. 5′ long tunnel like extension w. floor piece to join one shelter to another
FSI complete Anchor Kit – includes hammer drill, 2″ masonry bit, 4LB Sledge hammer, caulking gun, cement patch product, asphalt patch product, safety glasses.
Red or Green reflective striping above dirty and clean entry/exit ends of decon units
Additional windows per shelter
Skylights for all shelters
Cloth Velcro skylight cover — per skylight cover
Private Stencil X 2 per shelter/shower/pool/other — limited sizes/styles/colors avail.
Special Logo X 2 per shelter/shower/pool/other – limited sizes/styles/colors avail.
FSI Shelter – Center Divider Curtain for DAT3060, DAT3030, DAT3015, DAT3370, DAT4070, DAT4360 – includes QE and AL series similar sizes
FSI Shelter – Center Divider Curtain as above – for DAT5672/5800/6000/6600/6012/7500/9018 – includes QE and AL series similar sizes
FSI Shelter – Cross Divider Curtain, heavy duty, non see through, light color, removable, slip thru – for DAT3060, DAT3030, DAT3015, DAT3370, DAT4070, DAT4360 – includes QE and AL series similar sizes
FSI Shelter – 1/2 Cross Divider Curtain, heavy duty, non see through, light color, removable, slip thru – for sizes as found in DAT3060, DAT3030, DAT3015, DAT3370, DAT4070, DAT4360 – includes QE and AL series similar sizes
FSI Shelter – Cross Divider Curtain, heavy duty, non see through, light color, removable, slip thru – for DAT5672/5800/6000/6012/7500/9018 – includes QE and AL series similar sizes
FSI Shelter – ½ Cross Divider Curtain, heavy duty, non see through, light color, removable, slip thru – for DAT5672/5800/6000/6600/6012/7500/9018 – includes QE and AL series similar sizes
Insulating inside canopy complete with hanging hooks for all sizes of DAT series shelters inclusive of Isolation Shelters and Medical Surge Capacity Shelters. Heavy Duty 240 gr/yd., 200 denier nylon, polyurethane coated materials dramatically improves internal temperature performance in severe weather environs when units will be left in place for extended periods. UV/Chemical Resistant and Fire Retardant. This double canopy effectively offers 8″ of open air insulation from heat and cold between the 2 canopies. The cost is 20 % of the cost of the actual DAT series shelter unit itself
FSI 1/2 canopy in ‘Reflective White’ tm. HD Velcro attached to the outer canopy of DAT series shelters to act as a sun reflective/protective material OR as a weight bearing (snow load/etc. cover for the decon shelter. Can be made to fit DAT3015, DAT3060, DAT3030, DAT3070, DAT5672,DAT5700, DAT6000, DAT6012, and DAT7500 shelters.
Zippers on each end door Vs. flaps and tie downs
10″ M HD Gusseted Velcro flange attached to ends or side doors of shelters to allow attach to other units side to side or end to end
Two extra full man doors on each end of DAT series showers/shelters (smallest sizes may not accommodate two full extra man doors on each end)
Single or double center zipper(s) in middle of single large entry door on each end of the DAT series shelters
F-MD2 – 3
3 extra full man doors on each end of the DAT series showers/shelters. (smaller sized FSI shelters/showers may not be able to accommodate three man doors on each end)
Side door for shelters
PVC strip screen in man door widths of approx. 40″ to be pre-hung on inside air berm of isolation shelters for bump thru entry/exit to better ensure minimal air flow disruption and to meet CDC required 12+ air exch./hr. PER STRIP SCREEN
Additional approx. 17″ air duct cloth inlet/outlet for HVAC/Clothing/etc. w. tie closure
Roof mounted cloth ducting boots – approx. 6″ diameter X 9 ft. long. Used when direct roof ventilation is needed. May not be used for HVAC or any other heating equipment.
Full center length internal closed air ducting ‘plenum’ system for all FSI shelter systems with multiple air outlet vents (size of shelter dependent) – ideal for ducting in hot/cold air and/or for HEPA/other air filtration and decontamination with Cold Plasma/Ozone/other. — also ideal for hiding wiring, cables, etc. internally
Retrofit duct kit to add an HVAC duct to an existing FSI DAT series shelter/shower system – includes 19″ dia. template, glue, boot w. Velcro to affix around the cut opening, hanging HVAC duct piece
A complete set of one each of a high pressure/inflation deflation/over pressure valve to be installed on opposite end on opposite side of the DAT series shower or shelter FOR PNEUMATIC SHOWERS AND SHELTERS ONLY
Pneumatic replacement high pressure/inflation deflation/over pressure valves – per valve – spec. type with order FOR PNEUMATIC SHOWERS AND SHELTERS ONLY